Jump to content

You're browsing the 2004-2023 VATSIM Forums archive. All content is preserved in a read-only fashion.
For the latest forum posts, please visit https://forum.vatsim.net.

Need to find something? Use the Google search below.

Arrival Lists 3.2


Matt Middleton 1264577
 Share

Recommended Posts

Matt Middleton 1264577
Posted
Posted

Well there, hello.

 

Does any else have a problem with the Arrival Lists in 3.2 not showing AC that are effectively established on the ILS less than 5dme.

 

I have several times been caught out on TWR when AC have called me up and I didn't know anything about them.

 

Any help / guidance?

Link to comment
Share on other sites

Sam White 1214219
Posted
Posted

Had the same problem yesterday. On my SMR some aircraft showed up on the arrivals list, but most didn't, and on my ATM most did show up, but a couple did not show on either.

 

On the SMR I am using 'Easy VATSIM', and 'Easy Ground', and on the ATM I am using 'Mode C' correlation.

 

The ATM is connected to the SMR via proxy.

 

Also when the aircraft did not appear on the arrivals list, they also where not appearing in the 'planes list', 'sector inbound list', or 'flight plan list'.

VATSIM UK S2 Rated (Essex RTS)

Sam%20White.jpg

Link to comment
Share on other sites

Sam White 1214219
Posted
Posted

Quick update. When the aircraft is in the air they appear normally on all other lists apart from the arrivals list, but when they are on the ground they disappear from the other lists as well.

 

Have a look here:

ES32arrlist.PNG

ES32arrlist2.PNG

VATSIM UK S2 Rated (Essex RTS)

Sam%20White.jpg

Link to comment
Share on other sites

Gergely Csernak
Posted
Posted

The condition to put a plane to the arrival list is the following:

- The destination airport should be selected in the active RWY dialog as arrival.

- The plane should be closer to the destination than 10 NM

- It should not be a flight plan track without radar target

- The flight plan state should be simulated or terminated

 

Do you think that all the conditions are OK in your example?

Gergely.

EuroScope developer

Link to comment
Share on other sites

Sam White 1214219
Posted
Posted
The condition to put a plane to the arrival list is the following:

- The destination airport should be selected in the active RWY dialog as arrival.

- The plane should be closer to the destination than 10 NM

- It should not be a flight plan track without radar target

- The flight plan state should be simulated or terminated

 

Do you think that all the conditions are OK in your example?

The destination airport was selected

The aircraft was within 10NM

The aircraft where radar targets

I'm not too sure about the flight plan status though, I will check next time I log on.

VATSIM UK S2 Rated (Essex RTS)

Sam%20White.jpg

Link to comment
Share on other sites

Sam White 1214219
Posted
Posted

On the SMR the status of all arriving aircraft is no status, however they are all simulated on the ATM. I cannot change the flightplan status from the SMR, and I can from the ATM, however this has no effect on the SMR.

VATSIM UK S2 Rated (Essex RTS)

Sam%20White.jpg

Link to comment
Share on other sites

Gergely Csernak
Posted
Posted

I will check the arrival lists on easy correlation mode.

Gergely.

EuroScope developer

Link to comment
Share on other sites

  • 3 weeks later...
Sam White 1214219
Posted
Posted

If I check the 'Auto Start FP Tracks' box, the arrivals list works normally.

VATSIM UK S2 Rated (Essex RTS)

Sam%20White.jpg

Link to comment
Share on other sites

 Share