Matt Middleton 1264577 Posted July 6, 2014 at 10:41 PM Posted July 6, 2014 at 10:41 PM Well there, hello. Does any else have a problem with the Arrival Lists in 3.2 not showing AC that are effectively established on the ILS less than 5dme. I have several times been caught out on TWR when AC have called me up and I didn't know anything about them. Any help / guidance? What utter rubbish - https://gyazo.com/c741236275df2634ed8ab451698ea10d Link to comment Share on other sites More sharing options...
Sam White 1214219 Posted July 7, 2014 at 08:44 AM Posted July 7, 2014 at 08:44 AM Had the same problem yesterday. On my SMR some aircraft showed up on the arrivals list, but most didn't, and on my ATM most did show up, but a couple did not show on either. On the SMR I am using 'Easy VATSIM', and 'Easy Ground', and on the ATM I am using 'Mode C' correlation. The ATM is connected to the SMR via proxy. Also when the aircraft did not appear on the arrivals list, they also where not appearing in the 'planes list', 'sector inbound list', or 'flight plan list'. VATSIM UK S2 Rated (Essex RTS) Link to comment Share on other sites More sharing options...
Sam White 1214219 Posted July 7, 2014 at 07:01 PM Posted July 7, 2014 at 07:01 PM Quick update. When the aircraft is in the air they appear normally on all other lists apart from the arrivals list, but when they are on the ground they disappear from the other lists as well. Have a look here: VATSIM UK S2 Rated (Essex RTS) Link to comment Share on other sites More sharing options...
Gergely Csernak Posted July 13, 2014 at 02:28 PM Posted July 13, 2014 at 02:28 PM The condition to put a plane to the arrival list is the following: - The destination airport should be selected in the active RWY dialog as arrival. - The plane should be closer to the destination than 10 NM - It should not be a flight plan track without radar target - The flight plan state should be simulated or terminated Do you think that all the conditions are OK in your example? Gergely. EuroScope developer Link to comment Share on other sites More sharing options...
Sam White 1214219 Posted July 13, 2014 at 02:55 PM Posted July 13, 2014 at 02:55 PM The condition to put a plane to the arrival list is the following:- The destination airport should be selected in the active RWY dialog as arrival. - The plane should be closer to the destination than 10 NM - It should not be a flight plan track without radar target - The flight plan state should be simulated or terminated Do you think that all the conditions are OK in your example? The destination airport was selected The aircraft was within 10NM The aircraft where radar targets I'm not too sure about the flight plan status though, I will check next time I log on. VATSIM UK S2 Rated (Essex RTS) Link to comment Share on other sites More sharing options...
Sam White 1214219 Posted July 18, 2014 at 04:11 PM Posted July 18, 2014 at 04:11 PM On the SMR the status of all arriving aircraft is no status, however they are all simulated on the ATM. I cannot change the flightplan status from the SMR, and I can from the ATM, however this has no effect on the SMR. VATSIM UK S2 Rated (Essex RTS) Link to comment Share on other sites More sharing options...
Gergely Csernak Posted July 20, 2014 at 02:46 PM Posted July 20, 2014 at 02:46 PM I will check the arrival lists on easy correlation mode. Gergely. EuroScope developer Link to comment Share on other sites More sharing options...
Sam White 1214219 Posted August 10, 2014 at 04:45 PM Posted August 10, 2014 at 04:45 PM If I check the 'Auto Start FP Tracks' box, the arrivals list works normally. VATSIM UK S2 Rated (Essex RTS) Link to comment Share on other sites More sharing options...
Recommended Posts