Andrea Mazzoni Posted October 27, 2019 at 08:36 PM Posted October 27, 2019 at 08:36 PM Hello to everyone, yesterday I wasn't able to fly during CTP due to this problem with Xplane 10 and Xsquawkbox: I decide to fly with B777 Flight factor on Xplane10 and when I was connected, I have activated Audioforvatsim for the connection to the audio system. I know that with AFV is necessary active the radio also on the radio panel, so I activated, as you can see, the radio: But, nothing. the systems seems that wasn't able to recognize that I have actviated the radio. Just for info, on this 777, you can't see the "mic" light active over the microphone selector, only a green light, which is clearly visible on the left radio for COM1. Someone can told me if I made some mistakes or which is the possible reason that has caused this problem with AFV? Sometimes things get complicated. ATC on VATSIM as Milano Radar (LIMM_N_CTR) Twitch channel https://www.twitch.tv/italianalien21 Link to comment Share on other sites More sharing options...
Dhruv Kalra Posted October 27, 2019 at 08:44 PM Posted October 27, 2019 at 08:44 PM I think you need to click the volume knob labeled “VHF L” (directly below the VHF L Mic selector) Dhruv Kalra VATUSA ZMP ATM | Instructor | VATSIM Network Supervisor Link to comment Share on other sites More sharing options...
Board of Governors Simon Kelsey Posted October 27, 2019 at 11:37 PM Board of Governors Posted October 27, 2019 at 11:37 PM Unfortunately I believe FlightFactor are using non-standard datarefs for their radios (and possibly their electrics?), which makes it really difficult for the clients to read what state the radios are in (powered/unpowered etc). I believe JARDesign were doing something similar with their Airbus but have since updated it to use the standard X-Plane datarefs so they can actually be read. So really this is a problem for FlightFactor to solve in the long term. That said, I believe I've seen someone suggesting that they managed to get some success with a FlightFactor aircraft by selecting both VHF L and VHF R radios to on (so you get the green light above both), so that may be worth a try? (Lots of 'I believes' in there as I'm not an X-Plane user myself so just going off what I've heard). Vice President, Pilot Training Link to comment Share on other sites More sharing options...
Andrea Mazzoni Posted November 15, 2019 at 05:18 PM Author Posted November 15, 2019 at 05:18 PM Unfortunately I believe FlightFactor are using non-standard datarefs for their radios (and possibly their electrics?), which makes it really difficult for the clients to read what state the radios are in (powered/unpowered etc). I believe JARDesign were doing something similar with their Airbus but have since updated it to use the standard X-Plane datarefs so they can actually be read. So really this is a problem for FlightFactor to solve in the long term. That said, I believe I've seen someone suggesting that they managed to get some success with a FlightFactor aircraft by selecting both VHF L and VHF R radios to on (so you get the green light above both), so that may be worth a try? (Lots of 'I believes' in there as I'm not an X-Plane user myself so just going off what I've heard). No the problem is only with Flightfactor, because Jardesign A320 seems that haven't any problem. Sometimes things get complicated. ATC on VATSIM as Milano Radar (LIMM_N_CTR) Twitch channel https://www.twitch.tv/italianalien21 Link to comment Share on other sites More sharing options...
Robert Shearman Jr Posted November 15, 2019 at 05:29 PM Posted November 15, 2019 at 05:29 PM You missed the part where Simon said JARDesigns updated their software to comply. viewtopic.php?f=157&t=79900 Cheers, -R. Link to comment Share on other sites More sharing options...
Andrea Mazzoni Posted November 21, 2019 at 09:44 PM Author Posted November 21, 2019 at 09:44 PM You missed the part where Simon said JARDesigns updated their software to comply. viewtopic.php?f=157&t=79900 Yes, Jardesign it work, I know it because I use the A320 on Xplane 10, but the problem is with 777 Flightfactor. I would understand how it work the system about the audio for this aircraft. Maybe is better advise also the flightfactor developers.....If someone has found a solution, and he/she have this aircraft inside the simulator, any suggest is appreciate. Sometimes things get complicated. ATC on VATSIM as Milano Radar (LIMM_N_CTR) Twitch channel https://www.twitch.tv/italianalien21 Link to comment Share on other sites More sharing options...
Robert Shearman Jr Posted November 22, 2019 at 01:19 AM Posted November 22, 2019 at 01:19 AM xPilot now has dot-commands which override the radio state within the aircraft: .tx com1 .rx com1 on Cheers, -R. Link to comment Share on other sites More sharing options...
Birger L�¤ssing 1106808 Posted December 5, 2019 at 07:20 PM Posted December 5, 2019 at 07:20 PM Hello I have the same problems with the FF B777 but the FF B757 works.... FF=flight factor Link to comment Share on other sites More sharing options...
Birger LÃ�¤ssing 1106808 Posted December 5, 2019 at 07:46 PM Posted December 5, 2019 at 07:46 PM I have checked the solution with both radios on i can recieve the voice , but i can´t send . I will try it so on, it must work... Link to comment Share on other sites More sharing options...
Birger L�¤ssing 1106808 Posted December 5, 2019 at 09:38 PM Posted December 5, 2019 at 09:38 PM it works i can recieve and send with the FF B777 AFV on and then both radios an then Comm 1 (below the radios on) Link to comment Share on other sites More sharing options...
Recommended Posts