Anton Krishna Saputra 1012 Posted April 15, 2009 at 01:56 AM Posted April 15, 2009 at 01:56 AM I have this scenery file ILS25R:S006.06.32.350:E106.40.08.380:248 ILS25L:S006.07.49.170:E106.40.27.520:248 HOLDING:ESALA:270:1 AIRPORT_ALT:062 CONTROLLER:1:WIII_APP:127.9 CONTROLLER:2:WIII_TWR:118.1 @N:LNI007:2501:1:S006.18.25.000:E109.20.34.000:250:0:0:0 $FPLNI007:*A:I:MD90:400:WARS:0600:0600:250:WIII:1:00:2:40:WIPP:/V/:ANY W13 KIDET W13 IMU W13 DKI $ROUTE:LNI007:IMU DKI:0:0:12:DKI:3000 my question .. why the aircraft is not moving ? the label on control panel say ''LNI 007 on holding position" is there something wrong on my scenery or my sector file .. Link to comment Share on other sites More sharing options...
Gergely Csernak Posted April 15, 2009 at 03:02 PM Posted April 15, 2009 at 03:02 PM Anton, If the initial altitude of the plane is less than AIRPORT_ALT+1000 then it is [Mod - Happy Thoughts]umed to be on the ground. So the status will be holding position and not moving anywhere. If you need a plane initiated being airborne then simply select altitude or level above that value. In the @N line you can not enter FL values, just altitudes. The current value :250: is below the minimum 1062 in your case. As you request LNI000 to be at 3000 ft over DKI ( I do not know how far IMU from DKI), but some 5000 ft will change it to flying. Gergely. EuroScope developer Link to comment Share on other sites More sharing options...
Anton Krishna Saputra 1012 Posted April 16, 2009 at 12:36 AM Author Posted April 16, 2009 at 12:36 AM waks . thanks for the solution .. i change the value to 25000 .. and it's work ... what .. a great programme .. Link to comment Share on other sites More sharing options...
Anton Krishna Saputra 1012 Posted April 16, 2009 at 03:31 AM Author Posted April 16, 2009 at 03:31 AM can .i play multi sector ..and multi pilot for simulating? i'ts hard to handle many traffic by 1 person .. it's oc for 1 person controlling many aircraft , but for the pilot . ?? can we share computer for pilot ? Link to comment Share on other sites More sharing options...
Stephan Boerner 945550 Posted April 16, 2009 at 07:24 AM Posted April 16, 2009 at 07:24 AM This is supposed to be working in the current beta via sweatbox, but I have never tried that myself. Stephan Boerner VATEUD - ATC Training Director EuroScope Board of Designers | GVCCS Beta Tester EuroScope Quick Start Guide Link to comment Share on other sites More sharing options...
Gergely Csernak Posted April 16, 2009 at 09:52 AM Posted April 16, 2009 at 09:52 AM In the current beta there are many options to do that. You may use SweatBox, a local FSD server or connect via proxy with another scenario. But you should wait for the next public release. Gergely. EuroScope developer Link to comment Share on other sites More sharing options...
Anton Krishna Saputra 1012 Posted May 5, 2009 at 02:17 AM Author Posted May 5, 2009 at 02:17 AM hm .. i'm waiting for the next release .. i'm antusiated with this program for developing.. hey . can i help you for developing this software .. actually . i'm ATC'er in real life .. and i'm programing too ...i'ts so exciting .. Link to comment Share on other sites More sharing options...
Gergely Csernak Posted May 6, 2009 at 02:27 PM Posted May 6, 2009 at 02:27 PM Actually there are several testers but few of them are working on the plug-in development area. If you have a good idea, a good additional component or so and ready to do some C++ programming, then advise it me via the support mail. Gergely. EuroScope developer Link to comment Share on other sites More sharing options...
Recommended Posts